PRODUCT NAME SLJ41 Chlorinated Rubber Boat Topping Paint

BRIEF  One Pack water paint made from chlorinated rubber, modifier，pigments and extenders

FEATURES 
-Good adhesion, high hardness and gloss
-High chlorine content, has good flame retardancy and mildew resistance
-Excenllent water resistance, corrosion resistance and permeability
resistance
-Excellent resistance to dry and wet alternation and weather resistance
-Construction is not restricted by seasonal temperatures

RESISTANCE GUIDE
HEAT RESISTANCE   Up to 65℃ dry heat
WEATHERABILITY   Excellent
SOLVENTS         Resists splash and spillage of aliphatic solvents and mineral oil
ACIDS                  Resists splash and spillage of most inorganic acid fluid
ALKALIS              Resists splash and spillage of most alkalis
SALTS                 Resists splash and spillage of most alkali salts
WATER               Resists splash and spillage of fresh and salt water.
ABRASION         Excenllent

USES: Widely used on ship, offshore platform waterline area

TYPICAL PROPERTIES AND APPLICATION DATA
COLOR                         Colors
DENSITY                       1.3g/cm3
SOLIDS BY VOLUME              41%
SOLIDS BY WEIGHT               70%
SPREADING RATE                5.2 m2/kg      (60um DFT)
DRYING TIME(23℃)              Touch  4 Hr    Handle  24 Hr   
OVERCOAT INTERVAL(23℃)        Min 4 Hr   Max  none
STORAGE                         at least 12 months (dry, cool and under cover )
PACKAGING                     22kg


DIRECTIONS  Before using stir or using dynamic mixer mixing two components completely. Rate of cure will vary depending on temperature and other factors such as ventilation, film thickness, humidity, thinner. The temperature of stir will >15℃, otherwise thinner should be added for needed viscosity after stir. Overmuch thinner will lead sag and slow cure rate, thin film, thinner should beadded after mixed. Practical spreading rates may be reduced 5%—25% for wastage of different application conditions.

APPLICATION  

STEEL: The surfaces coated by primer or intermediate paint must be dry and clean,
remove oil, grease and other pollutants When overcoat on a two-component primer, wharf's pavement quality for old film or high-pressure water injection processing
should be taken if more than the longest accordance with time.
Don’t apply at temperatures below -10℃ or above 40℃. Don’t apply at relative humidity above 85% or when the surface is less than 3℃ above the dew point. In construction of lower than 0 ℃, the coated surface shall be free of ice, snow, etc.
Don’t apply if there is fog, rain, snow or strong wind.
BRUSH/ROLLER: Suitable for small areas only. Apply even coats of the mixed material to the prepared surface. Thin if necessary with up to 0-15% with X-3 Thinner X-3. Additional coats may be required to attain specified thickness.
CONVENTIONAL SPRAY: Thinning is not normally required, however 0-15% of Chlorinated Rubber Thinner X-3 can be added.
AIRLESS SPRAY: Thinning is not normally required, however 0-5% of Chlorinated Rubber Thinner X-3 can be added. Pump ratio is 23:1 or 32:1 and fluid tip is 0.38-0.43 mm.
Overcoating: Aged coating should be tested for lifting by a method such as ‘X’cut or crosshatch methods. If it lifts, remove it. The surface must be free of oil, grease and other contaminants.
Previous coat: Epoxy Coatings, Chlorinated Rubber Coatings
CLEAN UP: with Chlorinated Rubber Thinner X-3


SAFETY:Pay attention to the safety precautions before and after using this product. Users should comply with the provision of the respective country or local government. It’s dangerous or deadly to eating it. To avoid inhalation of thinner steams and spray mists.
Use protective wears correctly; the skin and eyes should avoid contacting it. Use with good ventilation. This product is flammable. All sources of ignition must be eliminated in, or near the working area. DO NOT SMOKE. Fight fire with foam, CO2 or dry chemical powder. On burning will emit toxic fumes.

Notes: The data in the manual is get from standard experiments and may be vary from different conditions in use. Please refer to the latest manual if the data is altered and we would not inform specially.