PRODUCT NAME Chlorinated Rubber Coat Slbs05

BRIEF  Primer intermediate finishing coating made from epoxy resin, acrylic acid resin, aliphatic polyurethane resin, pigments and extenders, function materials, modifier, etc

FEATURES
-Excellent ageing resistance
-Excellent resistance to pulverization and crack
-Use for a long time not yellowing
-Excellent heat insulation property
-Excellent reflecting sunlight

RESISTANCE GUIDE
HEAT RESISTANCE  Up to 120℃ dry heat
WEATHERABILITY   Excellent gloss and colour retention when exposed
SOLVENTS          Resists splash and spillage of aliphatic solvent, mineral oil
ACIDS               Suitable for splash and spillage to most acids
ALKALIS           Suitable for splash and spillage to most alkalis
SALTS               Excellent resistance to neutral and alkali salts
WATER             Excellent resistance to fresh and salt water, but not suitable for soaking
ABRASION       Good when fully cured.

USES:Widely on all kinds of pressure containers as PLG spherical tank, oil tanker,chemical pipeline equipment, chemical raw material tank, refrigerated trucks, external surface of the steel structure workshop, warehouse, etc, serve as heat insulation and cooling.

 TYPICAL PROPERTIES AND APPLICATION DATA
                                  Primer(glue)       Intermediate(glue)       Topcoat(glue)
COLOR                      Brown Red          Light Grey /White         White
DENSITY                     1.4g/cm3                   1.4g/cm3               1.2g/cm3
SOLIDS BY VOLUME        56%                   56%                42%
SOLIDS BY WEIGHT         76%                  76%                72%
SPREADING RATE          5.0 m2/kg(80um DFT) 5.0 m2/kg(80um DFT) 6.7 m2/kg(50um DFT)     
DRYING TIME(23℃)        Touch  4 Hr    Handle  24 Hr  
OVERCOAT INTERVAL(23℃)    Min 8 Hr   Max 7 Days 
STORAGE                 at least 12 months (dry, cool and under cover )
PACKAGING               Primer                  Part A: 21kg   Part B: 3kg
                                     Intermediate        Part A: 21kg   Part B: 3kg
                                    Topcoat                  Part A: 20kg   Part B: 4kg

 
 DIRECTIONS   Primer(glue), Intermediate(glue), Topcoat(glue) is a two pack, before using stir or using dynamic mixer mixing two components completely, then add part B to part A, and fully stir, life for 4 hours. Rate of cure will vary depending on temperature and other factors such as ventilation, film thickness, humidity, thinner. The temperature of stir will >15℃, otherwise thinner should be added for needed viscosity afterstir. Overmuch thinner will lead sag and slow cure rate, thin film, thinner should be added after mixed. Practical spreading rates may be reduced 5%—25% for wastage of different application conditions.
 
 APPLICATION   

STEEL: The surface coated by primer or intermediate paint should be dry and clean, no oil and other pollutants. When overcoat on a two-component film such as epoxy paint,  wharf's pavement quality for old film should be taken if more than the longest accordance with time.
Don’t apply at temperatures below 5℃ or above 40℃. Don’t apply at relative
humidity above 85% or when the surface is less than 3℃ above the dew point.       Don’t apply if there is fog, rain, snow or strong wind.
BRUSH/ROLLER: Suitable for small areas only. Apply even coats of the mixed material to the prepared surface. Thin if necessary with up to 0-15% with Special Thinner(Primer, Intermediate X-2, Topcoat X-5). Additional coats may be required to attain specified thickness.
CONVENTIONAL SPRAY: Thinning is not normally required, however 0-15% of Special Thinner(Primer, Intermediate X-2, Topcoat X-5) can be added.
AIRLESS SPRAY: Thinning is not normally required, however 0-5% of Special Thinner(Primer, Intermediate X-2, Topcoat X-5) can be added. Pump ratio is 23:1 or 32:1 and fluid tip is 0.33-0.38mm.
Overcoating: Aged coating should be tested for lifting by a method such as ‘X’cut or crosshatch methods. If it lifts, remove it. The surface must be free of oil, grease and other contaminants.
CLEAN UP: Special Thinner (Primer, Intermediate X-2, Topcoat X-5)

SAFETY:  Pay attention to the safety precautions before and after using this product. Users should comply with the provision of the respective country or local government. It’s dangerous or deadly to eating it. To avoid inhalation of thinner steams and spray mists.
Use protective wears correctly; the skin and eyes should avoid contacting it. Use with good ventilation. This product is flammable. All sources of ignition must be eliminated in, or near the working area. DO NOT SMOKE. Fight fire with foam, CO2 or dry chemical powder. On burning will emit toxic fumes.

Notes: The data in the manual is get from standard experiments and may be vary from different conditions in use. Please refer to the latest manual if the data is altered and we would not inform specially.