PRODUCT NAME Chlorinated Rubber Coat SLWF53

BRIEF  Multi-functional anticorrosive coatings made from fluorocarbon resin, modifier，pigments and extenders

FEATURES
-One of the most excellent comprehensive properties of coating, coating king
-Ozone proof，strong weather ability
-Excenllent heat and salt fog resistance
-Resistance to acid and alkali, organic solvent, high temperature medium,noncombustible
-Excenllent resistance to oil, water, contamination
-Protective coating in severe conditions

RESISTANCE GUIDE
HEAT RESISTANCE   Up to 250℃ dry heat
WEATHERABILITY   Well, ozone proof, up to 20 years outdoor use
SOLVENTS         Resists splash and spillage of organic solvents
ACIDS                 Resists splash and spillage of most inorganic acid fluid
ALKALIS             Resists splash and spillage of most alkalis
SALTS                 Resists splash and spillage of most alkali salts
WATER               Resists splash and spillage of fresh and salt water.
ABRASION        Excenllent

USES: Widely used on steel and concrete surface Aviation, shipping, oil platforms, Bridges, Marine facilities, storage tank etc
 
TYPICAL PROPERTIES AND APPLICATION DATA
COLOR                        Colors
DENSITY                       1.2g/cm3
SOLIDS BY VOLUME              40%
SOLIDS BY WEIGHT              72%
SPREADING RATE                8.3m2/kg      (40um DFT)
DRYING TIME(23℃)              Touch  4 Hr    Handle  24 Hr   
OVERCOAT INTERVAL(23℃)        Min 6 Hr       Max 7 Days
STORAGE                                at least 12 months (dry, cool and under cover )
PACKAGING                            Part A: 18kg   Part B: 3kg
MIXING RATIO (m/m)             Part A : Part B=6:1
CURE TIME(23℃)                 10min
POT LIFE(23℃)                     4 Hr

 DIRECTIONS Before using stir or using dynamic mixer mixing two components completely,Just mix a good raw material and mixing of raw materials before can not be together. Rate of cure will vary depending on temperature and other factors such as ventilation, film thickness, humidity, thinner. The temperature of stir will >15℃, otherwise thinner should be added for needed viscosity after stir.
Overmuch thinner will lead sag and slow cure rate, thin film, thinner should be added after mixed. Practical spreading rates may be reduced 5%—25% for wastage of different application conditions.

APPLICATION   

STEEL: The surface coated by primer or intermediate paint should be dry and clean, no oil and other pollutants. When overcoat on a two-component film such as epoxy paint,  wharf's pavement quality for old film should be taken if more than the longest accordance with time.Don’t apply at temperatures below 5℃ or above 40℃.
Don’t apply at relative humidity above 85% or when the surface is less than 3℃ above the dewpoint.
Don’t apply if there is fog, rain, snow or strong wind.
BRUSH/ROLLER: Suitable for small areas only. Apply even coats of the mixed material to the prepared surface. Thin if necessary with up to 0-15% with Fluorocarbon Thinner X-10. Additional coats may be required to attain specified thickness.
CONVENTIONAL SPRAY: Thinning is not normally required, however 0-15% of Fluorocarbon Thinner X-10 can be added.
AIRLESS SPRAY: Thinning is not normally required, however 0-5% of Fluorocarbon Thinner X-10 can be added. Pump ratio is 23:1 or32:1 and fluid tip is 0.38-0.43 mm.
Overcoating: Aged coating should be tested for lifting by a method such as ‘X’cut or crosshatch methods. If it lifts, remove it. The surface must be free of oil, grease and other contaminants.
Previous coat: Epoxy Coatings
CLEAN UP: with CSPE Thinner X-11 Thinner X-10

SAFETY:  Pay attention to the safety precautions before and after using this product. Users should comply with the provision of the respective country or local government. It’s dangerous or deadly to eating it. To avoid inhalation of thinner steams and spray mists.
Use protective wears correctly; the skin and eyes should avoid contacting it. Use with good ventilation. This product is flammable. All sources of ignition must be eliminated in, or near the working area. DO NOT SMOKE. Fight fire with foam, CO2 or dry chemical powder. On burning will emit toxic fumes.

Notes: The data in the manual is get from standard experiments and may be vary from different conditions in use. Please refer to the latest manual if the data is altered and we would not inform specially.