PRODUCT NAME SLC06-1 Alkyd Iron Red Anti-rust Coatings

BRIEF One Pack primer made from alkyd, modifier，iron oxide red pigments and extender

FEATURES
-Excellent adhesion on steel
-Excellent anti-rust ability

RESISTANCE GUIDE
HEAT RESISTANCE  Up to 80℃ dry heat
WEATHERABILITY   Well
SOLVENTS      Resists solvents such as alcohol, mineral oil, and other solvents.
ACIDS              Do not recommend for long-term contact with splash and spillage of acids fog and solution.
ALKALIS           Do not recommend for long-term contact with splash and spillage of alkalis fog and solution.
SALTS               Do not recommend contacting with most salts solution.
WATER             Resist rain and vapor, not suitable for long-term immersion and humidity
ABRASION      Good when fully cured.

USES:Widely used on steel as general corrosion protection

TYPICAL PROPERTIES AND APPLICATION DATA
COLOR                        Iron Oxide Red
DENSITY                       1.3g/cm3
SOLIDS BY VOLUME             42%
SOLIDS BY WEIGHT             72%
SPREADING RATE               8.0 m2/kg       (40um DFT)
DRYING TIME(23℃)             Touch  5 Hr    Handle  24 Hr   
OVERCOAT INTERVAL(23℃)       Min  24 Hr
STORAGE                        at least 12 months (dry, cool and under cover )
PACKAGING                     20kg

DIRECTIONS  Before using stir or using dynamic mixer mixing two components completely. Rate of cure will vary depending on temperature and other factors such as ventilation, film thickness, humidity, thinner. The temperature of stir will >15℃, otherwise thinner should be added for needed viscosity after stir. Overmuch thinner will lead sag and slow cure rate, thin film, thinner should beadded after mixed. Practical spreading rates may be reduced 5%—25% for wastage of different application conditions.

APPLICATION  

STEEL: Steel surface must be prepared by abrasive blast cleaning to ISO Standard Class Sa2.5 or power tool cleaning Class St3. The surface coated by shop primer
should be dry, clean and no dirt, take the second descaling where film damaged
or corrosion, and achieve Sa2.5 level or St3 level. Clear the zinc salt with high
pressure fresh water or sand. Weld and the damage parts processing to Sa2.5 level or
St3 level.
Don’t apply at temperatures below 5℃ or above 40℃. Don’t apply at relative humidity above 85% or when the surface is less than 3℃ above the dew point.
Don’t apply if there is fog, rain, snow or strong wind.
BRUSH/ROLLER: Suitable for small areas only. Apply even coats of the mixed material to the prepared surface. Thin if necessary with up to 0-15% with Alkyd Thinner X-1. Additional coats may be required to attain specified thickness.
CONVENTIONAL SPRAY: Thinning is not normally required, however 0-15% of e Alkyd Thinner X-1 can be added.
AIRLESS SPRAY: Thinning is not normally required, however 0-5% of Alkyd Thinner X-1 can be added. Pump ratio is 23:1 or 32:1 and fluid tip is 0.38-0.43 mm.
Overcoating: Aged coating should be tested for lifting by a method such as ‘X’cut or crosshatch methods. If it lifts, remove it. The surface must be free of oil, grease and other contaminants.
CLEAN UP: with Alkyd Thinner X-1

SAFETY: Pay attention to the safety precautions before and after using this product. Users should comply with the provision of the respective country or local government. It’s dangerous or deadly to eating it. To avoid inhalation of thinner steams and spray mists. Use protective wears correctly; the skin and eyes should avoid contacting it. Use with good ventilation. This product is flammable. All sources of ignition must be eliminated in, or near the working area. DO NOT SMOKE. Fight fire with foam, CO2 or dry chemical powder. On burning will emit toxic fumes.

Notes: The data in the manual is get from standard experiments and may be vary from different conditions in use. Please refer to the latest manual if the data is altered and we would not inform specially.