PRODUCT NAME SLH501 Super heavy duty epoxy coatings

BRIEF  A high solid, abrasion resistance of epoxy coatings, to provide long-term excellent rust resistance

FEATURES  
-Used in ballast tank of ship and platform
-Excellent seawater resistance.
-High solid, wear resistant coating is formed when cured
-Long-lasting anticorrosion performance
-Used in inner corrosion-resistant coating of oilfield pipeline, excellent resistance to moist heat
-High pressure airless spray

RESISTANCE GUIDE
HEAT RESISTANCE   Up to 140℃ dry heat
WEATHERABILITY     Some chalking and yellowing will occur with exterior exposure, however this will not detract from the resistance properties of the coating
SOLVENTS         Resists splash and spillage of most varsol, refined petroleum products and most common alcohols
ACIDS                 Suitable for splash and spillage to common acids
ALKALIS             Suitable for splash and spillage to strong alkalis
SALTS                 Excellent resistance to neutral and alkali salts
WATER               Excellent resistance to immersion in fresh and salt water
ABRASION        Good when fully cured.

USES: Widely used as ballast tank coating. The coating performance meet to the requirement of PSPC standard.

TYPICAL PROPERTIES AND APPLICATION DATA
COLOR                      Red (Primer),      White (Topcoat)
DENSITY                     1.4g/cm3              1.3g/cm3
SOLIDS BY VOLUME            62%             60%
SOLIDS BY WEIGHT             80%             76%
SPREADING RATE              8.56 m2/kg        9.23 m2/kg    (160um DFT)
DRYING TIME(23℃)            Touch  4 Hr    Handle  24 Hr    Full cure 7Days
OVERCOAT INTERVAL(23℃)      Min 8 Hr   Max 7 Days 
TREAD TIME(23℃)              16 Hr
STORAGE                              at least 12 months (dry, cool and under cover )
PACKAGING                          Part A: 21kg   Part B: 3kg
MIXING RATIO (m/m)           Part A : Part B=7:1
CURE TIME(23℃)               10min
POT LIFE(23℃)                    1 Hr

DIRECTIONS  Before using stir or using dynamic mixer mixing two components completely,Just mix a good raw material and mixing of raw materials before can not be together. Rate of cure will vary depending on temperature and other factors such as ventilation, film thickness, humidity, thinner. The temperature of stir will >15℃, otherwise thinner should be added for needed viscosity after stir.
Overmuch thinner will lead sag and slow cure rate, thin film, thinner should be added after mixed. Practical spreading rates may be reduced 5%—25% for wastage of different application conditions.

APPLICATION  

STEEL: Steel surface must be prepared by abrasive blast cleaning to ISO Standard Class Sa2.5 or power tool cleaning Class St3.Used in ballast tank of ship and platform, execute the standard of PSPC requirements. SLH06 epoxy zinc rich primer can be used as shop primer, The surface at least Sa2.5 level, and sandblasting roughness achieve 30-75um.
Shop prumer:BEdore coating, shop primer can be maintained, Clear with high pressure fresh water or and. Weld, corrosion area and the damaged parts processing to Sa2.5 level with sand.
BRUSH/ROLLER: Suitable for small areas only. Apply even coats of the mixed material to the prepared surface. Thin if necessary with up to 0-15% with X-2 thinner. Additional coats may be required to attain specified thickness.
CONVENTIONAL SPRAY: Thinning is not normally required, however 0-15% of X-2 thinner can be added.
AIRLESS SPRAY: Thinning is not normally required, however 0-5% of X-2 thinner can be added. Pump ratio is 32:1 or 45:1 and fluid tip is 0.43-0.48 mm.
Overcoating: Aged coating should be tested for lifting by a method such as ‘X’cut or crosshatch methods. If it lifts, remove it. The surface must be free of oil, grease and other contaminants.
Previous coat: SLH06 Zinc Rich Epoxy Primer or Shop Primer provened
CLEAN UP: with Epoxy Thinner X-2

SAFETY:Pay attention to the safety precautions before and after using this product. Users should comply with the provision of the respective country or local government. It’s dangerous or deadly to eating it. To avoid inhalation of thinner steams and spray mists.
Use protective wears correctly; the skin and eyes should avoid contacting it. Use with good ventilation. This product is flammable. All sources of ignition must be eliminated in, or near the working area. DO NOT SMOKE. Fight fire with foam, CO2 or dry chemical powder. On burning will emit toxic fumes.