PRODUCT NAME SLH87-1 Epoxy Iron Oxide Red Anti-rust Paint

BRIEF  Two Pack Amine Cured Epoxy Anticorrosive Primer

FEATURES
-Excellent adhesion on prepared substrate, good adhesion to next coat
-Good resistance to abrasion and impact
-Can be exposed to atmosphere and immersed in water
-Excellent chemical resistance

RESISTANCE GUIDE
HEAT RESISTANCE    Up to 140℃ dry heat
WEATHERABILITY      Some chalking and yellowing will occur with exterior exposure, however this
                                        will not detract from the resistance properties of the coating.
SOLVENTS                   Resists splash and spillage of most varsol and refined petroleum products.
ACIDS                            Suitable for splash and spillage to mild acids
ALKALIS                        Suitable for splash and spillage to strong alkalis
SALTS                            Excellent resistance to neutral and alkali salts
WATER                          Excellent resistance to immersion in fresh and salt water.
ABRASION                    Good when fully cured.

USES    Widely used in tank, ship, marine construction, mining machinery, pipelines, chemical   plant, etc.

TYPICAL PROPERTIES AND APPLICATION DATA
 COLOR                                          Brown Red (Primer)
 DENSITY                                         1.4g/ cm3
 SOLIDS BY VOLUME                    58%            
 SOLIDS BY WEIGHT                     76%            
 SPREADING RATE                        4.1m2/kg（100umDFT）
 DRYING TIME(23℃)                      Touch 4 Hr   Handle 24 Hr   Full cure  7Days
 OVERCOAT INTERVAL(23℃)      Min 8Hr    Max 7 Days
 STORAGE(dry, cool )                     at least 12 months (dry, cool and under cover )
 PACKAGING                                    Part A: 21kg   Part B: 3kg  per barrel
 MIXING RATIO (m/m)                     Part A: PartB=7:1
 CURE TIME(23℃)                         10min
 POT LIFE(23℃)                              4 Hr

DIRECTIONS  Before using stir or using dynamic mixer mixing two components completely,
Just mix a good raw material and mixing of raw materials before can not be
together. Rate of cure will vary depending on temperature and other factors
such as ventilation, film thickness, humidity, thinner. The temperature of stir
will >15℃, otherwise thinner should be added for needed viscosity after stir.
Overmuch thinner will lead sag and slow cure rate, thin film, thinner should be
added after mixed. Practical spreading rates may be reduced 5%—25% for
wastage of different application conditions.

APPLICATION  

STEEL:  Steel surface must be prepared by abrasive blast cleaning to ISO Standard Class Sa2.5 or power tool cleaning Class St3. Primer surface must keep dry and clean. The primer surface of damage, wedding and rusting must be prepared to Sa2.5 or St3. Zinc salt on the primer must be removed by abrasive or fresh water blasting.
Don’t apply at air temperature below 5℃ or above 40℃. Don’t apply at relative humidity above 85% or when air temperature is less than 3℃ above the dew point.
 Don’t apply if there is fog, rain, snow or strong wind. 
BRUSH/ROLLER: Suitable for small areas only. Apply even coats of the mixed material to the prepared surface. Thin if necessary with up to 0-15% with Epoxy Thinner X-2. Additional coats may be required to attain specified thickness. 
CONVENTIONAL SPRAY: Thinning is not normally required, however 0-15% of Epoxy Thinner X-2 can be added.
AIRLESS SPRAY: Thinning is not normally required, however 0-5% of Epoxy Thinner X-2 can be added. Pump ratio is 23:1 or 32:1 and fluid tip is 0.38-0.48 mm.
Overcoating: Aged coating should be tested for lifting by a method such as ‘X’cut or crosshatch methods. If it lifts, remove it. The surface must be free of oil, grease and other contaminants. 
Recommended previous coat: Zinc Rich Epoxy Primer
CLEAN UP: with Epoxy Thinner X-2

SAFETY:Pay attention to the safety precautions before and after using this product. Users should comply with the provision of the respective country or local government. It’s dangerous or deadly to eating it. To avoid inhalation of thinner steams and spray mists.
Use protective wears correctly; the skin and eyes should avoid contacting it. Use with good ventilation. This product is flammable. All sources of ignition must be eliminated in, or near the working area. DO NOT SMOKE. Fight fire with foam, CO2 or dry chemical powder. On burning will emit toxic fumes.

Notes: The data in the manual is get from standard experiments and may be vary from different conditions in use. Please refer to the latest manual if the data is altered and we would not inform specially.