PRODUCT NAME   SLH06 Epoxy Zinc Rich Primer

BRIEF Two Pack Zinc Rich Heavy-duty Epoxy Primer

FEATURES
-High level of zinc to provide corrosion resistance by sacrificial protection
-Excellent adhesion and rust resistance  on prepared substrates
-Good resistance to abrasion and impact
-Cutting and welding is allowed as shop primer
-Can be used as repair coating

RESISTANCE GUIDE
HEAT RESISTANCE   Up to 200℃ dry heat Severe conditions
WEATHERABILITY     Some chalking and yellowing will occur with exterior Exposure.
SOLVENTS          Resists splash and spillage of most arene solvents solvents and most common alcohols
ACIDS                          Do not use in acid conditions
ALKALIS                      Do not use in strong alkaline conditions unless suitably topcoated
SALTS                          Excellent resistance to neutral and alkali salts when suitably topcoated
WATER                        Suitably for immersion in fresh and salt water when suitably topcoated
ABRASION                  Very good when fully cured.

USES: widely used as shop primer and maintenance paint of steel, long-term anti-rust Primer of ship and bridge.

TYPICAL PROPERTIES AND APPLICATION DATA
  COLOR                          Gray
 DENSITY                        2.6g/ cm3
  SOLIDS BY VOLUME           52%
SOLIDS BY WEIGHT              88%
 SPREADING RATE                2.5m2/kg（80umDFT）
 DRYING TIME(23℃)             Touch 1 Hr    Handle  24 Hr    Full cure 7Days
 OVERCOAT INTERVAL(23℃)      Min 8 Hr    Max 6 Mon  （shop primer）
                                                                              Max 7 Days  （anticorrosive primer）
 STORAGE(dry, cool )                     At least 12 months
 FLASH POINT                                27℃
 PACKAGING                                   Part A: 33kg Part B: 2kg  (3 part sometime) per barrel
 MIXING RATIO (m/m)                   Part A: PartB=33:2
 CURE TIME(23℃)                       15min
 POT LIFE(23℃)                           4 Hr

DIRECTIONS Before using stir or using dynamic mixer mixing two components completely, Just mix a good raw material and mixing of raw materials before can not be together. Rate of cure will vary depending on temperature and other factors such as ventilation, film thickness, humidity, thinner. The temperature of stir
will >15℃, otherwise thinner should be added for needed viscosity after stir.
Overmuch thinner will lead sag and slow cure rate, thin film, thinner should beadded after mixed. Practical spreading rates may be reduced 5%—25% for wastage of different application conditions

APPLICATION  

STEEL: Round off all rough welds, sharp edges and remove weld spatter. Remove grease, oil and other contaminants. Steel surface must be prepared by abrasive blast cleaning to ISO Standard Class Sa2.5 or power tool cleaning Class St3.
Don’t apply at temperatures below 5℃ or above 40℃. Don’t apply at relative humidity above 85% or when the surface is less than 3℃ above the dew point. 
Don’t apply if there is fog, rain, snow or strong wind. 
BRUSH/ROLLER: Suitable for small areas only. Apply even coats of the mixed material to the prepared surface. Thin if necessary with up to 0-15% with Epoxy Thinner X-2. Additional coats may be required to attain specified thickness. 
CONVENTIONAL SPRAY: Thinning is not normally required, however 0-15% of Epoxy Thinner X-2 can be added.
AIRLESS SPRAY: Thinning is not normally required, however 0-5% of Epoxy Thinner X-2 can be added. Pump ratio is 23:1 or 32:1 and fluid tip is 0.43-0.48 mm.
Overcoating: Aged coating should be tested for lifting by a method such as ‘X’cut or crosshatch methods. If it lifts, remove it. The surface must be free of oil, grease and other contaminants.
Subsequent coat: Epoxy Coating .
CLEAN UP: with Epoxy Thinner X-2.

SAFETY :Pay attention to the safety precautions before and after using this product. Users should comply with the provision of the respective country or local government. It’s dangerous or deadly to eating it. To avoid inhalation of thinner steams and spray mists.
Use protective wears correctly; the skin and eyes should avoid contacting it. Use with good ventilation. This product is flammable. All sources of ignition must be eliminated in, or near the working area. DO NOT SMOKE. Fight fire with foam, CO2 or dry chemical powder. On burning will emit toxic fumes.

Notes: The data in the manual is get from standard experiments and may be vary from different conditions in use. Please refer to the latest manual if the data is altered and we would not inform specially.